• CPU: S5P4418, dynamic frequency from 400Mhz to 1.4GHz
• PMU Power Management: Implemented by a Cortex-M0 MCU, support software power-off, and RTC alarm power-up functions
• DDR3 RAM: 1GB
• eMMC: 8GB
• Wireless：802.11 b/g/n
• Bluetooth：4.0 dual mode
• MicroSD Slot: 1 x MicroSD Slot
• Audio: 3.5mm jack/Via HDMI
• Microphone: 3.5mm jack
• USB Host: 1 x USB 2.0 Host
• Micro USB: 1 x MicroUSB, USB 2.0 for both data transmission and power input
• LCD Interface: 0.5 mm pitch 45-pin SMT FPC seat, for full-color LCD (RGB: 8-8-8)
• HDMI: microHDMI,1080P60 output
• DVP Camera Interface: 0.5mm pitch 24-pin FPC seat.
• LVDS：0.5mm pitch 24-Pin FPC seat
• GPIO1: 2.54mm pitch 40pin, compatible with Raspberry Pi's GPIO. It includes UART, SPI, I2C, PWM, IO and etc
• ADC: onboard ADC pin header
• Serial Debug Port:2.54mm pitch 4-Pin header
• Antenna Interface: IPEX connector
• User Key: 1 x Power , 1 x Boot Mode Switch
• LED: 1 x Power LED, 1 x System LED
• RTC: RTC Pins
• PCB Size(mm): 75 x 40, 8 layer， ENIG
• Power Supply: DC 5V/2A
• Working Temperature: -40℃ to 80℃
• OS/Software: u-boot, Android5.1, Debian8

Linux

Boot OS from TF Card
Android and Debian

GPIO Pin Spec

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	VDD_5V
3	I2C0_SDA	4	VDD_5V
5	I2C0_SCL	6	DGND
7	GPIOD8/PPM	8	UART3_TXD/GPIOD21
9	DGND	10	UART3_RXD/GPIOD17
11	UART4_TX/GPIOB29	12	GPIOD1/PWM0
13	GPIOB30	14	DGND
15	GPIOB31	16	GPIOC14/PWM2
17	SYS_3.3V	18	GPIOB27
19	SPI0_MOSI/GPIOC31	20	DGND
21	SPI0_MISO/GPIOD0	22	UART4_RX/GPIOB28
23	SPI0_CLK/GPIOC29	24	SPI0_CS/GPIOC30
25	DGND	26	GPIOB26
27	I2C1_SDA	28	I2C1_SCL
29	GPIOC8	30	DGND
31	GPIOC7	32	GPIOC28
33	GPIOC13/PWM1	34	DGND
35	SPI2_MISO/GPIOC11	36	SPI2_CS/GPIOC10
37	AliveGPIO3	38	SPI2_MOSI/GPIOC12
39	DGND	40	SPI2_CLK/GPIOC9

The NanoPi S2's LCD interface is a top FPC connector while the LCD interface on the NanoPi M3/M2/Fire and NanoPC-T2/T3 is a bottom contact. The pin sequence of the NanoPi S2's LCD interface is the reverse of the pin sequence of the LCD interface on the other Nano boards.

RGB LCD Interface Pin DescriptionRGB LCD Interface Pin Description

Pin#	Name	Description
44, 45	VDD_5V	5V Output, it can be used to power LCD modules
1,6,7,8,9,17,26,35	DGND	Ground
36-43	Blue MSB to LSB	RGB blue
27-34	Green MSB to LSB	RGB green
18-25	Red MSB to LSB	RGB red
16	GPIOB25	available for users
15	GPIOC15	occupied by FriendlyARM one wire technology to recognize LCD models and control backlight and implement resistive touch, not applicable for users
14	XnRSTOUT Form CPU	low when system is reset
13	VDEN	signal the external LCD that data is valid on the data bus
12	VSYNC	vertical synchronization
11	HSYNC	horizontal synchronization
10	LCDCLK	LCD clock, Pixel frequency
5	I2C2_SCL	I2C2 clock signal, for capacitive touch data transmission
4	I2C2_SDA	I2C2 data signal, for capacitive touch data transmission
3	GPIOC16	interrupt pin for capacitive touch, used with I2C2
2	NC	Not connected

Debug Port（UART0）

Pin#	Name
1	DGND
2	VDD_5V
3	UART_TXD0
4	UART_RXD0

DVP Camera Interface Pin Description

Pin#	Name
1, 2	SYS_3.3V
7,9,13,15,24	DGND
3	I2C0_SCL
4	I2C0_SDA
5	GPIOB14
6	GPIOB16
8,10	NC
11	VSYNC
12	HREF
14	PCLK
16-23	Data bit7-0

ADC

ADC rang: 0~1.8V

Pin#	Name
1	1.8V reference output
2	ADC3
3	ADC4
4	DGND
5	AUD_LIN2, audio line in 2 of ES8316

LVDS

Pin#	Name
1	VDD_5V
2	VDD_5V
3	VDD_5V
4	LVDS_Y0M
5	LVDS_Y0P
6	DGND
7	LVDS_Y1M
8	LVDS_Y1P
9	DGND
10	LVDS_Y2M
11	LVDS_Y2P
12	DGND
13	LVDS_CLKM
14	LVDS_CLKP
15	DGND
16	LVDS_Y3M
17	LVDS_Y3P
18	DGND
19	GPIOC15
20	DGND
21	I2C2_SCL
22	I2C2_SDA
23	GPIOC16
24	DGND

Note:

1. SYS_3.3V: 3.3V power output
2. VDD_5V: 5V power output5V. When the external device’s power is greater than the MicroUSB’s the external device is charging the board otherwise the board powers the external device.The input range is 4.7V ~ 5.6V
3. All pins are 3.3V, output current is 5mA
4. GPIO1' pin description is different from that of the NanoPi 2. Here is a comparison table40 pins GPIO comparison table
5. For more details refer to the document:NanoPi-S2-1710-Schematic.pdf